For quick login in and fast entrance.
M’enregistrer FAQ Connexion 
Poster un nouveau sujet Répondre au sujet  [ 4768 messages ]  Aller à la page Précédente  1 ... 197, 198, 199, 200, 201, 202, 203 ... 318  Suivante

Sam 04 Mai 2019 14:13

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Sam 04 Mai 2019 14:13 
Hors ligne
Observateur Avisé
Observateur Avisé
Avatar de l’utilisateur

Inscription: Ven 12 Avr 2019 18:01
Skywalker Image a écrit:
Pas d'accord
je prends cette fois le vol JT610

image

Première action du MACS après la rentrée des volets
Action MACS 2 est due au réarmement suite à l'action du pilote sur le trim électrique manuel
Les volets sont ressortis: plus d'action du MCAS
Action 3 douteuse, STS ou MACS écourtée
Mais à partir de là on voit bien que l'action du MACS est écourtée, annulée par l'action sur le trim de manche. ça se voit très bien sur les actions 14 et 15. Le déplacement du plan fixe dû au MACS Noze Down est très faible car immédiatement contrée par l'action du trim de manche
On voit bien que le plan fixe inverse son mouvement quand le pilote trimme pour contrer le MACS

Le MACS est un système anti-décrochage et il n'agit qu'une seule fois et c'est suffisamment violent.
Ce qui change avec le nouveau logiciel ce sont les conditions de réarmement qui semble-t-il éviteront qu'il se réarme indéfiniment. On ne sait pas encore vraiment puisque la FAA vient de retoquer le "nouveau" logiciel

Citation:
The function is reset once angle of attack falls below the Angle of Attack threshold or if manual stabilizer commands are provided by the flight crew. If the original elevated AOA condition persists, the MCAS function commands another incremental stabilizer nose down command according to current aircraft Mach number at actuation.

La phrase est anbiguë. Je comprends que si les conditions AoA... mais après que le MCAS ait été resetté



Pas vraiment ambigüe quand même ?

¨The function is reset once angle of attack falls below the Angle of Attack threshold or if manual stabilizer commands are provided by the flight crew. If the original elevated AOA condition persists, the MCAS function commands another incremental stabilizer nose down command according to current aircraft Mach number at actuation "

LA fonction est " reset " dans deux cas

1°) Quand l'AoA retombe en dessous du seuil qui a déclenché l'intervention du MCAS ( en langage pilote, quand le pilote sous facteur de charge arrive aux grands angles, ET REND la main ... donc l'AoA retombe en dessous du seuil, ce qui reset le MCAS

2°) OR si les yoke switches ont été " provided by the flight crew "

Franchement je ne vois aucune ambiguïté dans ces deux phrases.

D'autre part le système MCAS N'EST PAS, selon Boeing un systeme anti décrochage

Maneuvering Characteristics Augmentation System (MCAS) :

MCAS (Maneuvering Characteristics Augmentation System) is implemented on the 737 MAX to enhance pitch characteristics with flaps UP and at elevated angles of attack. The MCAS function commands nose down stabilizer to enhance pitch characteristics during steep turns with elevated load factors and during flaps up flight at airspeeds approaching stall.

Je vous accorde que la nuance est subtile :-) Mais Boeing donne un autre renseignement :

" The maneuvering characteristic Augmentation System ( MCAS ) allows the stabilizer to move in the nose down direction when approaching high angles of attack at high speed

Clairement me semble t-il le system a été conçu pour prévenir un violent pitch up, mais à grande vitesse et sous facteur de charge, ce qui éloigne de la notion commune de décrochage en approche, ou en virage juste avant en Flaps Up.

D'ailleurs je me demande si les avions ne se sont pas crashés suite à un violent pitch up ( facteur de charge >0 effort désespéré pour cabrer, et perte de contrôle violente et immédiate résultant de ce pitch up brutal dont le MCAS devait justement protéger l'avion...

Mais vraiment on ne peut pas raisonner et échanger si on n'a pas les mêmes définitions du MCAS.
Il me paraît raisonnable d'utiliser celles d'avant les accidents, soit


BOEING 737-/7-/8 System Differences Volume 1
FLIGHT CONTROLS Training Manual
-748- 27-41 de Janvier 2017

_________________
Aviation Analyst
Fail to prepare... Prepare to Fail
Aviation Analyst website


  
home Haut
 Profil  
Répondre en citant le message  
Aider le Site avec PayPal

Sam 04 Mai 2019 18:02

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Sam 04 Mai 2019 18:02 
Hors ligne
Observateur Avisé
Observateur Avisé
Avatar de l’utilisateur

Inscription: Sam 17 Aoû 2013 12:27
Aviation Analyst Image a écrit:
Pas vraiment ambigüe quand même ?
Exact:

Citation:
To summarise; MCAS will trim the Stabilizer down for 10 seconds (2.5 deg nose down) and pause for 5 seconds and repeat if the conditions (high angle of attack, flapdisengaged) continue to be met. Using electric pitch trim will only pause MCAS for 5s; to deactivate it you need to switch off the STAB TRIM CUTOUT switche
https://www.thegreyeagles.org/Portals/0/Images/737%20MAX%20-%20MCAS_1.PDF

Quand à la définition retenue pour le MCAS, j'ai l'impression qu'il ne faut surtout pas parler de "dispositif anti-décrochage", les inspecteurs FAA serait capables de se rendre compte que Boeing les prend pour des imbéciles et pourraient exiger une re-certifications des performances de décrochage...

_________________
Critique Low-Cost


  
home Haut
 Profil  
Répondre en citant le message  

Sam 04 Mai 2019 18:51

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Sam 04 Mai 2019 18:51 
Hors ligne
Observateur Avisé
Observateur Avisé
Avatar de l’utilisateur

Inscription: Ven 12 Avr 2019 18:01
Skywalker Image a écrit:
Aviation Analyst Image a écrit:
Pas vraiment ambigüe quand même ?
Exact:

Citation:
To summarise; MCAS will trim the Stabilizer down for 10 seconds (2.5 deg nose down) and pause for 5 seconds and repeat if the conditions (high angle of attack, flapdisengaged) continue to be met. Using electric pitch trim will only pause MCAS for 5s; to deactivate it you need to switch off the STAB TRIM CUTOUT switche
https://www.thegreyeagles.org/Portals/0/Images/737%20MAX%20-%20MCAS_1.PDF

Quand à la définition retenue pour le MCAS, j'ai l'impression qu'il ne faut surtout pas parler de "dispositif anti-décrochage", les inspecteurs FAA serait capables de se rendre compte que Boeing les prend pour des imbéciles et pourraient exiger une re-certifications des performances de décrochage...


Tout à fait. Tout le monde assimile le décrochage, à basse vitesse en Flaps Up, à l'approche des grands angles. Pour cela le 737 est pourvu avec le Stall Management system, lequel utilise d'ailleurs deux tube pitot dédiés, pour la vitesse et le SMYD pour plein de choses ( ADIRU ) dont évidemment l'AoA qu'il reçoit directement et non depuis l'ADIRU.

Ce qui était nécessaire pour la certif, c'était de démontrer les qualités de vol hors du domaine de vol normal, à grande vitesse et sous facteur de charge élevé. À grande vitesse l'incidence est relativement faible, et le facteur de charge diminue fortement et rapidement la marge par rapport à la perte de contrôle ( je préfère ce terme à celui de décrochage ) Sous l'effet d'un facteur de charge significatif, il y a toujours tendance à un pitch Up soudain, plus ou moins brutal. Apparemment le MAx ne rentrait pas dans les clous. La tendance au pitch up devait être trop forte, et il fallait donc le MCAS.

C'est pourquoi en définitive, je pense que dans les deux cas les avions ne sont pas partis en piqué de plus en plus prononcé, et finalement fatal ( grande vitesse, hors trim, et profondeur devenue totalement inefficace ) mais que dans les deux cas il y a eu apparition de ce pitch up brutal, et sa conséquence la perte de contrôle, et les g négatifs. Pour ceux qui ont pu l'expérimenter, ils comprendront ce phénomène de pitch up avec l'exemple suivant ( ce n'est qu'un exemple ) Mettez vous à 250 kts par exemple, en virage serré plain pot, en palier, ( c'est comme une recette de cuisine ) enfoncez doucement le palonnier extérieur à fond et lâchez tout d'un coup( manche et palonnier ). Pitch up extémement brutal et garanti, passage dos et nez dans le sol....

Pour en revenir aux avions on voit bien le cabré du désespoir surtout sur le JT 610 ) avec les control forces associées, et la perte de contrôle...

Sinon deux petites remarques à vos post : ET 302 : Vous dites ( moi aussi ) quand l'AP désengage, l'avion est bien trimé, et qu'il aurait fallu revenir à ce réglage... AP enclenché à 05:39:23 et 220 kts et déclenché 33 " après à 05:39:57 et 250 kts, il est donc normal que l'AP ait trimé nose down.
Entre AP déclenché et fin du trim capt, 41 " pendant lesquelles l'avion accélère de 250 à 340 kts ( VMO )

Le bon réglage trim à 340 kts est fatalement plus faible que celui à 250 kts.

Et enfin si vous me permettez, quant aux deux tentatives trim pilot, juste avant l'AND fatal, elles ne sont pas sans effet comme vous le dites, mais elle permettent bien une remontée du trim, remontée légère mais remontée tout de même. Coolhand l'a observé aussi.
Tout à fait cordialement.

_________________
Aviation Analyst
Fail to prepare... Prepare to Fail
Aviation Analyst website


  
home Haut
 Profil  
Répondre en citant le message  

Sam 04 Mai 2019 19:59

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Sam 04 Mai 2019 19:59 
Hors ligne
Observateur Avisé
Observateur Avisé
Avatar de l’utilisateur

Inscription: Ven 12 Avr 2019 18:01
niuniu Image a écrit:
Bonjour à tous après ce ''férié-chômé'' :mrgreen:
Une petite vidéo que je trouve instructive : les 5 premières minutes du vol, comme elles auraient du se dérouler, en particulier les 2 premières. Bon, c'est au simu.
https://www.youtube.com/watch?time_cont ... nEDU4I0r-Q



J’ai pris le temps de regarder la video qu’a postée niuniu (page 198) qui nous dit que c’est une bonne description d’un décollage normal, suivant les procédures.

Oh que non ! Du moins en ce qui concerne le pilotage, mais de fait je pense qu’elle veut montrer le décollage de l’ET302 en espérant que l’auteur a voulu montrer les difficultés du Capt ET 302, et non pas ses propres qualités de pilote. Anyway …

En revanche on peut décrypter aisément au vu du PFD et du FMA ce qu’il se passe lors d’un décollage normal avec un FMC normalement renseigné avant le D/L

Il est intressant de noter que l’A/T n’est pas un systeme isolé qui gère la poussée, mais une partie de l’AFDS qui lui réagit tout aussi bien aux ordres ( physiques ) du pilote sur le mode control panel ( MCP), que du FMS. Le statut de l’Autothrottle n’est que la résultante des ordres de l’AFDS ( soit pilote, soit FMS )

C’est pour cela que sur le FMA on doit bien avoir conscience que s’affiche à gauche les Autothrottle modes, au centre le Roll mode (AP/FD ) et à droite le pitch mode ( AP/FD)

Tout ce qui est en Magenta, est un target , V2 mais aussi les maneuvring speeds ( (5, 1, UP ) qui sont censées être maintenue par la pente tant qu’ils sont apparents. Pour V2, puisqu’il s’agit de montée initiale V2 est un target ( one engine out ), quand tout va bien il est remplacé par un target blanc à V2 + 15 , que l’AP/FD va respecter.


Donc rapidement sur la vidéo : Avant la mise en poussée le Throttle mode est ARM ( en blanc ) ainsi que LNAV

La poussée est affichée après le lâcher des freins => Throttle Mode : N1, Le pitch mode à droite affiche TO/GA en vert, comme le N1. De façon classique tout ce qui est vert signifie que le mode est engagé, tout ce qui est blanc signifie que le mode est armé. ( Par TO/GA il faut entendre plein pot ou poussée réduite au T/O °
Le roll mode est actif en vert et indique HDG ( RNW HDG )

Le target de montée est 7000 ' magenta. LNAV est armé ( en blanc ) et s’engagera à 50 '. La radio sonde en blanc est à -4

À 85 kts le Throttle mode ( à gauche du FMA ) passe en THR HOLD

Au D/L on observe aussi en vert sur l’échelle des vitesse V1 = 131 kits, VR, et V2 = 147 kits. En passant VR, Z terrain = 620 ' et RA = -2. Au lâcher des freins Z terrain = 580 donc piste montante, légèrement.

On voit l’index ( petit ) blanc qui matérialise V2 + 15= 162, vitesse de montée initiale juqu’à l’altitude d’accélération ( mini 400 ' )

Au décollage, on ne voit pas la maneuvring speed 5, mais seulement 1 & UP, le D/L s’effectue donc volets 1. ( affichages en vert, normal tout cela est en action ) ( Flaps Schedule )

On voit bien le passage en LNAV à 50 ', et la maneuvring speed 1, indique la vitesse à laquelle on passe les volets sur UP. 1 va disparaître et UP restera affiché. ( avion lisse )

À 400’ toujours THR HOLD, qui passe en ARM à 800’

À 1500’ ( altitude de réduction ) le throttle mode passe de ARM à N1 ( poussée de montée )

On verra passer aussi les target de montée ( 250 kts jusqu’à 10 000 ' et 290 kts ensuite )

À 4100’ alti, le pitch mode de l’AFDS passe de TO/GA à VNAV SPEED, le throttle mode de l’A/T à gauche indique toujours N1 ( poussée climb) depuis 1500 '

J’ai dû en oublier. Bon décollages !

_________________
Aviation Analyst
Fail to prepare... Prepare to Fail
Aviation Analyst website


  
home Haut
 Profil  
Répondre en citant le message  

Sam 04 Mai 2019 22:35

 
MessagePosté: Sam 04 Mai 2019 22:35 
Hors ligne
Principicule de Taxiway
Principicule de Taxiway
Avatar de l’utilisateur

Inscription: Sam 06 Avr 2019 22:26
LE RAPPORT FINAL DEVRAIT COMPORTER LA POSITION DE TOUS LES CONTACTEURS ET LES DIVERS AFFICHAGES
Quant au rôle de la fonction MCAS (fonction du FCC en fait) tantôt on cite basse vitesse (d'où fort AoA)
tantôt high speed (avec fort AoA ça donne facteur de charge), et aussi steep turns (lesquels demandent fort AoA car besoin de forte portance)
le seuil d'intervention en AoA dépend de la vitesse

dans les interventions et les textes il y a le terme "reset" qui fait confusion, est-ce que c'est un arrêt, une remise en action sur ordre, ou un retour à la posture d'attente pour voir si les conditions d'adtion sont réunies (durée 5 sec)

que le MCAS répète son intervention obstinément est visible sur le cas 610 (rapport) et très bien détaillé dans les compléments ajoutés par Boeing au manuel après l'accident

ce fil est passionnant voire passionné, c'est un peu un puzzle, et il manque quelque part un endroit où les pièces bien placées seraient rassemblées, faisant référence unique et connue pour progresser. Les sources des extraits de documentation seraient bienvenues.
En tout cas on apprend beaucoup sur l'appréhension de l'automatisation par les utilisateurs.


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 14:20

 Re:
MessagePosté: Dim 05 Mai 2019 14:20 
Hors ligne
Principicule de Taxiway
Principicule de Taxiway
Avatar de l’utilisateur

Inscription: Sam 06 Avr 2019 22:26
jiceherre Image a écrit:
LE RAPPORT FINAL DEVRAIT COMPORTER LA POSITION DE TOUS LES CONTACTEURS ET LES DIVERS AFFICHAGES
Quant au rôle de la fonction MCAS (fonction du FCC en fait) tantôt on cite basse vitesse (d'où fort AoA)
tantôt high speed (avec fort AoA ça donne facteur de charge), et aussi steep turns (lesquels demandent fort AoA car besoin de forte portance)
le seuil d'intervention en AoA dépend de la vitesse

dans les interventions et les textes il y a le terme "reset" qui fait confusion, est-ce que c'est un arrêt, une remise en action sur ordre, ou un retour à la posture d'attente pour voir si les conditions d'adtion sont réunies (durée 5 sec)

que le MCAS répète son intervention obstinément est visible sur le cas 610 (rapport) et très bien détaillé dans les compléments ajoutés par Boeing au manuel après l'accident



ce fil est passionnant voire passionné, c'est un peu un puzzle, et il manque quelque part un endroit où les pièces bien placées seraient rassemblées, faisant référence unique et connue pour progresser. Les sources des extraits de documentation seraient bienvenues.
En tout cas on apprend beaucoup sur l'appréhension de l'automatisation par les utilisateurs.



j'ajoute
pas bien clair sur les "switches" de la console centrale, il y a eu une modification entre les versions antérieures et le MAX (si j'ai bien compris), y a t il une possibilité de manipulation erronée en confondant les deux dispositions? (ancienne disposition enracinée dans la mémoire, troublée par le stress)
est-ce que les deux ont été coupés "en même temps" ou avec un délai, que se passe t -il si on remet l'un et pas l'autre?


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 19:38

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 19:38 
Hors ligne
Principicule de Taxiway
Principicule de Taxiway
Avatar de l’utilisateur

Inscription: Mar 02 Juin 2009 19:35
Pour changer un peu de la technique pure, et des hypothèses à confirmer au moment de la sortie du rapport définitif, voici un article intéressant sur l'évolution des rapport entre la FAA, les certificateurs et la hiérarchie Boeing et sur certains sacrifices faits au détriment de la sécurité au nom du respect des plannings et des impératifs commerciaux.
Cf: le diagramme du nouveau process.

https://www.seattletimes.com/business/b ... /#comments

Edit:
Et la suite de l'audition du sous-comité transport du sénat sur l'évolution du dossier 737 max aura lieu le 15 mai.
A suivre sur "c-span.org"
http://www.nytimes.com/aponline/2019/05 ... aring.html


Modifié en dernier par Jacaj le Dim 05 Mai 2019 20:37, modifié 1 fois.

  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 20:07

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 20:07 
Hors ligne
Novice Aérien
Novice Aérien

Inscription: Sam 28 Mar 2015 14:22
Jacaj Image a écrit:
Pour changer un peu de la technique pure, et des hypothèses à confirmer au moment de la sortie du rapport définitif, voici un article intéressant sur l'évolution des rapport entre la FAA, les certificateurs et la hiérarchie Boeing et sur certains sacrifices faits au détriment de la sécurité au nom du respect des plannings et des impératifs commerciaux.
Cf: le diagramme du nouveau process.

https://www.seattletimes.com/business/b ... /#comments


Cet article du Seattle Times est extrêmement intéressant et permet de mieux comprendre l'environnement du processus de certification par la FAA et ses " représentants" chez les constructeurs US.
Même s'il ne surprend pas certaines personnes au fait du système, il contient des informations qui, décortiquées, devraient obligatoirement faire réfléchir les autorités " non US " quant aux conditions dans lesquelles sont validés certains dossiers.


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 20:41

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 20:41 
Hors ligne
Pilote de Funiculaire
Pilote de Funiculaire
Avatar de l’utilisateur

Inscription: Lun 02 Fév 2009 14:58
Localisation: Entre ciel et mer
[quote="R14L32"

Cet article du Seattle Times est extrêmement intéressant et permet de mieux comprendre l'environnement du processus de certification par la FAA et ses " représentants" chez les constructeurs US.
Même s'il ne surprend pas certaines personnes au fait du système, il contient des informations qui, décortiquées, devraient obligatoirement faire réfléchir les autorités " non US " quant aux conditions dans lesquelles sont validés certains dossiers.[/quote]

Ce problème de MCAS pourrait bien s’avérer être le petit bout de laine qui va détricoter la sacrée pelote du processus de certification entre Boeing and la FAA...

_________________
Quand une connerie est possible, elle a déjà été faite. Quand elle est impossible, elle se fera.


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 20:48

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 20:48 
Hors ligne
Pilote de Funiculaire
Pilote de Funiculaire
Avatar de l’utilisateur

Inscription: Lun 11 Fév 2008 16:07
Localisation: Quart Sud-Est
Jacaj Image a écrit:
Pour changer un peu de la technique pure, et des hypothèses à confirmer au moment de la sortie du rapport définitif, voici un article intéressant sur l'évolution des rapport entre la FAA, les certificateurs et la hiérarchie Boeing et sur certains sacrifices faits au détriment de la sécurité au nom du respect des plannings et des impératifs commerciaux.
Cf: le diagramme du nouveau process.

https://www.seattletimes.com/business/b ... /#comments



L'article est derrière a paywall.

_________________
Amicalement,
MCR boy
"En théorie, il n'y a pas de différence entre la théorie et la pratique..."


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 20:49

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 20:49 
Hors ligne
Amiral de l'Air
Avatar de l’utilisateur

Inscription: Mer 03 Juin 2009 14:15
Localisation: Près de Morlaix-Ploujean (LFRU)
Image

_________________
Image


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 20:55

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 20:55 
Hors ligne
Pilote de Funiculaire
Pilote de Funiculaire
Avatar de l’utilisateur

Inscription: Lun 02 Fév 2009 14:58
Localisation: Entre ciel et mer
MCR boy Image a écrit:
Jacaj Image a écrit:
Pour changer un peu de la technique pure, et des hypothèses à confirmer au moment de la sortie du rapport définitif, voici un article intéressant sur l'évolution des rapport entre la FAA, les certificateurs et la hiérarchie Boeing et sur certains sacrifices faits au détriment de la sécurité au nom du respect des plannings et des impératifs commerciaux.
Cf: le diagramme du nouveau process.

https://www.seattletimes.com/business/b ... /#comments



L'article est derrière a paywall.


Engineers say Boeing pushed to limit safety testing in race to certify planes, including 737 MAX
May 5, 2019 at 6:00 am

By Dominic Gates and Mike Baker
Seattle Times staff reporters

In 2016, as Boeing raced to get the 737 MAX certified by the Federal Aviation Administration (FAA), a senior company engineer whose job was to act on behalf of the FAA balked at Boeing management demands for less stringent testing of the fire-suppression system around the jet’s new LEAP engines.

That June he convened a meeting of all the certification engineers in his unit, who collectively agreed with his assessment. Management initially rejected their position, and only after another senior engineer from outside the MAX program intervened did managers finally agree to beef up the testing to a level the engineer could accept, according to two people familiar with the matter.

But his insistence on a higher level of safety scrutiny cost Boeing time and money.

Less than a month after his peers had backed him, Boeing abruptly removed him from the program even before conducting the testing he’d advocated.

The episode underscores what The Seattle Times found after a review of documents and interviews with more than a dozen current and former Boeing engineers who have been involved in airplane certification in recent years, including on the 737 MAX: Many engineers, employed by Boeing while officially designated to be the FAA’s eyes and ears, faced heavy pressure from Boeing managers to limit safety analysis and testing so the company could meet its schedule and keep down costs.

That pressure increased when the FAA stopped dealing directly with those designated employees — called “Authorized Representatives” or ARs — and let Boeing managers determine what was presented to the regulatory agency.

“The ARs have nobody supporting them. Nobody has their backs,” said one former Authorized Representative who worked on the 737 MAX and who provided details of the engineer’s removal from the program. “The system is absolutely broken.”

FAA-designated oversight engineers are supposed to enjoy protection from management pressure. Removing one who proves a stickler for safety regulations will inevitably produce a chilling effect on others who see the consequences of being too rigid about safety concerns, said John Goglia, former member of the National Transportation Safety Board (NTSB).

“It negates the whole system,” said Goglia. “The FAA should have come down on that really hard.”

Following two deadly 737 MAX crashes off the coast of Indonesia and in Ethiopia that killed 346 people, and the subsequent grounding of the airplane worldwide, the certification of the jet has come under intense scrutiny, including a slew of lawsuits, congressional hearings and a criminal investigation.

None of the people interviewed were involved in certifying the Maneuvering Characteristics Augmentation System, the flight-control software implicated in the two crashes. But one area of scrutiny is sure to be the delegated system under which Boeing employees, paid by the company but acting as FAA designees, did the detailed certification work. It may slow down plans by the FAA and Boeing for a future certification regimen that would further erode the FAA’s oversight.





Boeing, in a statement responding to Seattle Times questions, said that FAA procedures, including regular, FAA-mandated training, “ensure Boeing employees serving in this capacity act independently on behalf of the FAA.”

It added that “there are processes in place to carefully evaluate any concerns regarding the AR’s ability to act independently.” The company declined to comment on individual cases cited in this story.
Yet as the FAA has increasingly delegated certification tasks to Boeing itself, it’s also made changes to the reporting structure that leave its designees to fend for themselves inside the company.

While a few former employees involved in certifications said they handled the pressure as a regular part of the job, others described the work environment as hostile, focused on achieving FAA approval within schedule and cost targets. Some of those workers spoke on condition of anonymity to protect professional relationships or for fear of retribution.

This echoes the findings of a Seattle Times investigation in March of what happened on the FAA side of the MAX certification. Within the FAA, its safety engineers worked under constant pressure from their managers to delegate more and more work to Boeing itself, and to speedily approve the safety assessments the Boeing designees came up with.

On the Boeing side of that process, the removal of the senior engineer acting as an FAA Authorized Rep was an extreme example that highlights the broader negative impact of two changes: The FAA no longer appoints its own ARs, instead leaving that to Boeing. And these designees now rarely interact with the FAA directly, according to former Boeing ARs interviewed by The Times.

They said these changes have stripped them of protection and given managers more opportunity to push for shortcuts.

In a statement, the FAA said it oversees the Boeing certification system “to ensure procedures are followed.” The agency also said it has “received no whistleblower complaints or any other reports … alleging pressure to speed up 737 MAX certification.”

Boeing managers are supposed to undergo “undue pressure” training to ensure that they aren’t crossing boundaries with the FAA’s representatives. And some ARs said that, despite some tensions, their managers were respectful of the role.

Fred Stong, an AR who worked on electrical systems at Boeing, said his experience was that everyone works through differences to reach common ground. He said he was always assertive in his role and didn’t face any problems.

“At no time in my career would anybody dare to pressure me,” Stong said.

Yet the former AR on the MAX said managers overseeing that jet’s certification were “extremely aggressive” about anything that affected the program cost or schedule.

“Managers were pounding on the ARs to get what the company needs in terms of reduced testing,” he said. “If it costs the company time and money, they’d pound on you to change the test design.”

The radical shift from DERs to ARs
Before 2004, those Boeing technical employees who worked safety on behalf of the FAA were called “Designated Engineering Representatives,” or DERs. Though paid by Boeing, they were appointed by the FAA and reported directly to their technical counterparts at the FAA.

What changed since 2004 is that safety engineers, now called Authorized Representatives, are appointed by and report to Boeing managers.

The opaque bureaucratic name for this new structure — Organization Designation Authorization (ODA) — masks the significant change: Instead of having individual Boeing employees authorized as FAA reps, Boeing now has an entire organization within the company so authorized. The individual FAA Authorized Reps — Boeing engineers — report up the chain to their Boeing managers, not the FAA.

A veteran aviation-safety engineer who over the decades worked for long stints as a DER at Boeing and later as a Boeing AR on a variety of projects including the MAX, said there’s “nothing inherently wrong” with the FAA delegating safety certification — provided it retains oversight.

This consultant asked for anonymity to protect his current livelihood doing certification work for multiple aviation companies.

Working as a DER with smaller aviation companies that don’t have an ODA designation, it’s his job to ensure their products comply with all safety regulations. On those projects, he can consult directly with FAA technical people if any problem arises or if he needs advice on what exactly may be required to demonstrate compliance.

“If I need guidance, I call my FAA adviser,” he said. “I’m overseen directly by the FAA. And every year there is a pretty robust audit of my activity before the FAA will delegate me for the following year.”

His experience working as an AR at Boeing and other companies was quite different.

“Under ODA, the FAA no longer manages the people making the compliance findings,” he said. “They never even talk to them.”

And because Boeing appoints the representatives, he said, accountability is severely curtailed. “If the company is happy with their decisions, obviously, they’ll be kept in their jobs.”

Under the old system, “we knew we’d lose our livelihood if we didn’t maintain the integrity of making decisions the way the FAA would do it,” the consultant said. “That check is no longer there.”

The FAA, contradicting the accounts of the former Authorized Representatives interviewed, said that ARs “have frequent interaction and access to FAA personnel to communicate concerns directly.”

However, a copy of one version of the Boeing ODA manual, an internal document labeled proprietary but obtained by The Times, told ARs with concerns about their workload or pressure from managers to first report them to the AR administrator, who is a higher level Boeing manager.

The manual also states that AR performance will be judged in part by whether they are “completing their duties in a timely and cooperative manner.”

It’s a Boeing manager who determines if an individual representative’s performance is sufficiently cooperative, as evidenced by the experience of Mike Levenson, who has worked as an FAA representative at several companies and served in an AR role at Boeing for five years until 2013.

He said that while there’s always a pressure on FAA representatives in an aviation world full of deadlines and cost considerations, most industry managers are able to find a balance to ensure the ARs have independence. He said he didn’t find that to be the case at Boeing.

Levenson worked on certifying aircraft repairs at Boeing and said he certified more than 500 in his time there, though he did not work on the MAX. On three occasions, he declined to certify repairs. The first two times, Levenson said, he got called into a supervisor’s office.

On the third occasion, in June 2013, a proposed repair clearly did not meet all FAA requirements, he said. After he declined to approve it, Levenson said, his manager “told me to go back and find compliance or my contract would not be extended.”

Levenson agreed to do additional work and consulted with other colleagues but still couldn’t certify the repair’s compliance.

“When I reported this to my manager, I was told this was unacceptable and was summarily dismissed the following day,” Levenson said.

The FAA said it has no record of Levenson filing a complaint. Levenson said he talked to the agency but didn’t file anything formally.

MAX inherits 737 legacy issues
The removal from the MAX program of the FAA’s Authorized Rep who insisted upon stricter engine fire-suppression testing is briefly summarized in a February 2017 report obtained by The Seattle Times. The report does not name the engineer, and the two people who described what happened spoke on condition that he not be named.

In the report, prepared by the three unions that represent FAA technical staff, the incident was listed among a long series of problematic decisions made under the current system of delegating FAA certification and oversight to Boeing.

The engineer removed from the program had more than two decades of experience at Boeing doing certification work on behalf of the FAA. Managers transferred him to Boeing’s “Central Engineering” unit, with no particular job description, and appointed as his replacement on the MAX team an engineer with relatively little experience in certification.

Four additional concerns specific to the 737 MAX were listed in the 2017 report. All were related to certification of legacy systems inherited from the earliest 737 models that were found by FAA technical staff to be noncompliant with the latest safety regulations.

These involved a lack of redundancy in the rudder cables; a too-high surface temperature allowed in the fuel tank; insufficient fireproofing around the plane’s auxiliary power unit in the tail; and using high-power wiring to connect to a switch inside the fuel tank.

All these issues were flagged by safety engineers working at the FAA as requiring fixes before the MAX could be certified.

The MAX won certification anyway after managers on the Boeing side of certification insisted that these were non-issues and managers on the FAA side agreed to let it move ahead with these shortcomings unaddressed.

All were waved through by the Boeing ODA and signed off by FAA management, according to the union report.

The FAA, in its statement to The Times, said it ordered the findings to be investigated at the time but said it wouldn’t address the specific items “because of the ongoing investigations into the aircraft’s certification.”

A better oversight structure
When Acting FAA Administrator Dan Elwell appeared before the U.S. Senate subcommittee on aviation in March, he was asked if the FAA could pull the oversight of air safety back in-house instead of delegating it to Boeing and other manufacturers.

“It would require roughly 10,000 more employees and another $1.8 billion for our certification office,” Elwell told the senators.

But that’s assuming the FAA would end delegation of oversight completely and take back all the certification work for a new airplane. That’s impractical, not only for the lack of resources, but also because all the leading-edge technological expertise needed is concentrated inside Boeing and its suppliers.

Many of the FAA’s safety engineers formerly worked for Boeing. But when they leave industry to work for the government, after a few years they inevitably lose touch with the latest innovations.

As the former NTSB member Goglia puts it: “You can’t stay on the pointy end of the arrow and work for the government.”

The former Boeing Authorized Rep who described the current system as “broken” agrees.

“It’s impossible for someone sitting at a desk at the FAA to keep up with the technology,” he said. “Once you step out, it will bypass you really fast.”

Still, he said, there’s no need to contemplate a wholesale removal of delegation from industry. Instead, he said, what’s needed is to have the same Boeing engineers continue to do the safety evaluations, but to have them chosen by and reporting to the FAA — in other words, to revert to the old DER structure of oversight.

The former AR said that worked well because the FAA “was able to see into the design process from the beginning and have direct input as it was developed.”

“I’m not asking for the FAA to add 10,000 engineers,” he said. “Keep the same ARs as today. Just change who they report to, who is overseeing them. That doesn’t mean transferring the work to the FAA.”

John Cox, chief executive of Safety Operating Systems and formerly the top safety official for the Air Line Pilots Association, said that following the accidents and questions raised about how the errant flight control system on the MAX was certified, “there probably needs to be a review of the ODA system.”

“The (older) DER approach worked extremely effectively,” Cox said. “If engineers are working on behalf of the FAA, they should have a direct technical liaison with the FAA.”

And Goglia, the former NTSB member, said the AR system, with these engineers appointed by and reporting to Boeing, may need to be adjusted.

“I like the older system better than Boeing, or any manufacturer, having that kind of control,” Goglia said.

Moving toward complete self-certification
Yet before the MAX crashes, the FAA was heading in exactly the opposite direction: toward more delegation of oversight, with FAA participation reduced to a bare minimum.

A 2012 report to the FAA by a committee co-chaired by a Boeing representative and the FAA’s top aviation safety official, Ali Bahrami, recommended increased delegation of oversight to industry, working toward a “future state” beyond ODA with another deliberately obscure bureaucratic name: Certified Design Organization, or CDO.

If Boeing were to achieve CDO status, its employees could certify their own designs. Employees doing the certification work would not be designees technically working on behalf of the FAA, just Boeing engineers working for Boeing.

This would be true self-certification, but has not yet been implemented.

Levenson said such a shift would increase safety risks for the industry.

“It’s a horrible idea,” Levenson said. “There’s not enough oversight as it is now. That would remove almost all oversight.”

The former AR on the MAX who provided details of the engineer’s removal said he spoke to The Seattle Times because he hopes for action to reverse the industry’s direction.

He said the two crashes that claimed so many lives in Indonesia and Ethiopia starkly emphasize the need to force the FAA to go back to a DER-style structure, where those working at Boeing on behalf of the FAA are directly overseen by agency technical experts.

“Unfortunately, in our industry, the pendulum swings when people die,” he said. “Let those people’s deaths mean something.”

Seattle Times researcher Miyoko Wolf contributed to this story.

Dominic Gates: 206-464-2963 or dgates@seattletimes.com; on Twitter: @dominicgates.
Mike Baker: 206-464-2729 or mbaker@seattletimes.com; on Twitter: @ByMikeBaker.

_________________
Quand une connerie est possible, elle a déjà été faite. Quand elle est impossible, elle se fera.


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 20:58

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 20:58 
Hors ligne
Pilote de Funiculaire
Pilote de Funiculaire
Avatar de l’utilisateur

Inscription: Lun 11 Fév 2008 16:07
Localisation: Quart Sud-Est
Merci !

_________________
Amicalement,
MCR boy
"En théorie, il n'y a pas de différence entre la théorie et la pratique..."


  
home Haut
 Profil  
Répondre en citant le message  

Dim 05 Mai 2019 21:41

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Dim 05 Mai 2019 21:41 
Hors ligne
Principicule de Taxiway
Principicule de Taxiway
Avatar de l’utilisateur

Inscription: Mar 02 Juin 2009 19:35
MCR boy a écrit:
L'article est derrière a paywall.


Je n'ai pas ce problème... peut être un nombre trop important d'articles lus ?
Je te suggère un effacement de cookies.
ou installer un ad-blocker ? (uBlock origin par exemple)

Le schéma qui manque au texte:
Image


  
home Haut
 Profil  
Répondre en citant le message  

Lun 06 Mai 2019 10:06

 Re: Un Boeing 737MAX d'Ethiopian s'écrase en route vers Nairobi
MessagePosté: Lun 06 Mai 2019 10:06 
Hors ligne
Gonfleur d'Hélice
Gonfleur d'Hélice

Inscription: Jeu 26 Jan 2017 14:01
C'est Boeing qui le dit !

''Des ingénieurs de Boeing avaient identifié, dès 2017, des dysfonctionnements dans les systèmes d'alerte des pilotes du 737 Max en raison d'une erreur de logiciel, soit un an avant l'accident de Lion Air, a révélé dimanche le constructeur assurant toutefois que les hauts dirigeants n'en avaient rien su jusqu'à la tragédie indonésienne.
«En 2017, plusieurs mois après le début des livraisons du 737 MAX, des ingénieurs de Boeing avaient constaté que le système d'affichage du 737 MAX ne répondait pas correctement aux exigences de l'alerte de la (sonde d'angle d'attaque) AOA», explique Boeing dans un communiqué.''
http://www.lefigaro.fr/flash-eco/boeing ... 7-20190505


  
home Haut
 Profil  
Répondre en citant le message  
Afficher les messages postés depuis:  Trier par  
Poster un nouveau sujet Répondre au sujet  [ 4768 messages ]  Aller à la page Précédente  1 ... 197, 198, 199, 200, 201, 202, 203 ... 318  Suivante

Heures au format UTC + 1 heure


Qui est en ligne

Utilisateurs parcourant ce forum: Aucun utilisateur enregistré et 8 invités


Vous ne pouvez pas poster de nouveaux sujets
Vous ne pouvez pas répondre aux sujets
Vous ne pouvez pas éditer vos messages
Vous ne pouvez pas supprimer vos messages

Aller à:  
Flux RSS Flux RSS Liste des flux Liste des flux
0 Développé par phpBB® Forum Software © phpBB Group
Traduction par phpBB-fr.com
phpBB SEO